1 Bug, 1 Probable bug and 1 request

[Caspian]

Bug
On Vista 64, in Setup the "Apply" Button is always lit but can not be clicked. Clicking "OK" does save setting.
[edit] clicking Apply does make it "Flash" but it is stil lit up as if there are still changes that need to be applied. Making a change, clicking Apply then Cancel does save your changes. This is not so much a bug I guess, more of an annoyance because it looks like you still have outstanding changes, when in fact they have been saved. Or not, you can't tell, but you can always click apply or OK to make sure.

Probable bug - [edit] more details and this is a bug
Using the Pass mouse click feature
When Pass Mouse Click is Turned on mouse response becomes VERY slow and erratic.
I can not have "Pass Once" enabled. I have to spam click to get a click to pass. Just one click will cause my window focus to shift and the spinning "Vista Thinking" icon and switch back without passing the click.
Just now my windows are up and have a small square in the middle of the screen (Likely the last click location). Mousing over this square jive me the "thinking" icon and clicking it brings up the Program not responding icon for Keyclone. While this was there Keyclone still worked. When I changed my WoW resolution the square went away on that WoW. Changing the resolution did not affect the performance or issues. On the WoW that still had the square I chose the option to shut down Keyclone and it killed off the Master Keyclone program.

Enhancement Request - Would like the ability to launch my WoWs from within Keyclone, using the command editor, but not necessarily when Keyclone launches. Perhaps a "Launch Now" button for the command and Check box for "Launch at Keyclone Start". This would help me because a lot of times I have one or two WoWs up and do not want it to launch them all. It also helps with testing things out when I don't want all of them to start up and just test a couple things out.

I tested this with 2 WoWs - 1 on each monitor and with both on the same monitor (using each of my monitors in separate tests)

My Setup
Vista 64
Latest Keyclone, just downloaded and installed. Run as administrator.
Quad core Intel Q6600
8 GB Ram
ATI 4850 w/512 MB Ram
2x Monitor
1st @ 1920x1200 - Clones run here at 800x600
2nd@ 1680x1050 - Primary runs here in windowed mode at 1900x1200 (also tested at 1680x1050)
These are the Max setting for my monitors.
I have 6 WoWs total in separate directories with pretty much everything but WTF and the actual binaries symlinked.

None of these issues are critical for me. If you need more information or need me to try something out I would be happy to help out either in this thread, via PM or via my Paypal email, which ever you think is best.

Thanks!

[Maxion]

You can already launch your wow commands at any time you want, instead of having the run at start option on, just put the command in the box in the main window and hit connect. Using that you can put in whichever commands you want to launch at that time.

[Caspian]

You can already launch your wow commands at any time you want, instead of having the run at start option on, just put the command in the box in the main window and hit connect. Using that you can put in whichever commands you want to launch at that time.

It took a minute to figure that out but I got. It is not the button I was looking for but it is the functionality I wanted. I did not know that was there. Well I saw the box but it was never populated so I didn't know what it was for.

Thanks!

[keyclone]

the command box can be used to launch one or more commands (ie: wow1 or wow1;wow2;wow3)
or connect to another keyclone on another machine (ie: 192.168.10.15:1320).
you can also run a command on another machine (ie: machine2:wow3)

[warbringer]

That's a damn good tip, I never realised that!